Industrial Communication
UNMANAGED Ethernet Switches
- Suitable for industrial applications
- Compact IEEE 802.3 Layer 2 industrial switches
- Plug-and-play functionality.
- Support store and forward transmission
- Wide Operating temperature -40﮿C to 85﮿C (-E Model)
- 12/24/48VDC redundant dual input power design
- With Fiber Port and Gigabit versions also available
- EN50121-4 approved
MANAGED Ethernet Switches
- Suitable for industrial applications
- Provides 5 instances that each can support µ-Ring, u-Chain or sub-ring type of flexible uses; Supports up to 5 rings in one device.
- µ-Ring for redundant cabling, recovery time< 10ms in 250 devices
- Supports Green Ethernet IEEE802.3az EEE(Energy Efficient Ethernet) to optimize power consumption
- CLI, Web based management, SNMP V1/V2c/V3, Telnet server for management
- EN50121-4(Rail Traffic), NEMA TS2 approved
ETHERNET TO FIBER MEDIA CONVERTOR
- Fast Ethernet and Gigabit versions available
- Supports Single mode and Multimode
- Managed and Unmanaged
- Dual power supply design for power Redundancy
- Store-and-Forward mode and Pass through mode (set by DIP Sw)
- Support LFPT (Link Fault Pass Through)
- EN50121-4 approved
SERIAL SERVER (Serial to Ethernet converter)
- Supports Web management
- Redundant multiple host devices
- Supports both Point to Point and Point to Multipoint operation
- LED alarm display for power failures
- Supports RS232/485/422
- Supports direct IP mode, Virtual COM mode and paired mode
POWER OVER ETHERNET (PoE)
- Industrial power over Ethernet (POE)
- 4 port to 24 port available
- Managed and Unmanaged versions available
- Transmits power and data over Ethernet networks
- 24/48VDC redundant dual input power
- Supports negative voltage power inputs with isolated RS232 console port
- µ-Ring for redundant cabling, recovery time< 10ms in 250 devices
- Supporting central EMS for management of up to 50 SmartView server and maximum up to 25000 device tool
IEC61850-3 Ethernet Switches
- Suitable for power substation application
- Redundancy isolated low voltage and high voltage power inputs
- Supports GOOSE message that complies with IEC61850 standard to achieve zero packet loss
- Supports IEEE1588 for precise time sync
- Din-rail and wall mount design
- EN50121-4, approved
IP67 Rugged Ethernet Switches
- With M12 and M23 connectors to protect from shock and vibration
- IP67 Grade housing to protect from water, oil and dust.
- Available in Fast and Gigabit versions
- EN50121-4
Serial to Fiber Optic Converter
- Suitable for point to point, Daisy chain, cable redundancy, Ring redundancy topologies
- Extends serial transmission distance up to 2km, 30km, 60km
- Supports RS232, RS 422, RS485(2&4 wire) transmission to dual fiber connections
- 5KV isolation for serial signal
- Enhanced serial baud rate up to 1024kbps
Profibus to Fiber Optic Converter
- Suitable for point to point, Daisy chain, cable redundancy, Ring redundancy topologies
- Extends serial transmission distance up to 2km, 30km, 60km
- Redundant dual Power inputs(12/24/48VDC)
- Protocol transparent. This product also be applied to other networks using RS485 interface
- Auto Baud Up to 12Mbps
- 5KVrms for serial port
- EN61000-6-2, EN61000-6-4 certified
CAN Bus to Fiber Optic Converter
- Supports CAN2.0A, CAN2.0B, ISO11898-2 standard
- Extends serial transmission distance up to 2Km, 30Km
- Auto Baud Rate up to 1Mbps
- 5KVrms isolation for CAN Bus port
- 120 Ohm terminator selectable by DIP SW
- , EN61000-6-2, EN61000-6-4 certified
Ethernet to Fiber Media Converters (commercial grade)
- Fast Ethernet and Gigabit versions available > FMC-CH17, 2U, 19”, 17-Slot chassis with
- Supports Single mode and Multimode with single or dual built-in power for
- Managed and Unmanaged AC or DC
- Auto-negotiation and forced mode > FMC Units are hot swappable
- Supports LFPT and FEFI
- Forward 9K jumbo packets in converter mode (100M/Full)
Simple Converter Chassis
Industrial 4G LTE gateway
- 4G LTE, GPS, IEEE 802.11b/g/n/ac WiFi, 2x SIM card, 3x GbE RJ45 LAN/WAN + 2x DI + 1x DO, 1x RS232 com port
- Supports concurrent dual band WiFi With 802.11n 2T2R (2.4GHz), and 802.11ac 2T2R (5GHz)
- Supports 4G LTE/ WiFi/ UTP port to configure WAN ports for failover redundant
- Builid-in various VPN protocols for security, Firewall & IPS, ACL & Authentication by MAC/User to enhance access security
- IEEE 802.11 a/b/g/n/ac, multiple SSID, captive portal for WiFi hotspot
- Web, CLI ,SNMP, TR069, SMS for management and configuration
- EN-60950-1, CE, FCC, Rail Traffic EN50121-4 certified
- Heavy industrial grade EMS, EMI, EN61000-6-2, EN61000-6-4 certified
- Rugged metal, IP30 protection & Fanless design
4G LTE Router
- Supports multi-band connectivity with FDD 4G LTE/ TDD 4G LTE/ 3G WCDMA/2G GSM/ LTE Cat4
- 2 SIM card, 4G LTE antenna, 1x WAN (10/100Base-TX) + 3x LAN (10/100Base-TX UTP), 2x DI + 1x DO, 3x Serial Com port (2x RS232, 1x RS485)
- GPS, GNSS to get your location on earth, and obtains map information using Google Map (Optional)
- Supports 3x Serial port (1x RS484, 2x RS232) for IoT and automation application, ModBus RTU and ModBus/TCP gateway, MQTT
- Supports Alarm message : DO, SNMP Trap, E-mail
- Supports SNMP, TR069,Web, Telnet, CLI for management
- Supports dual Image firmware upgrade by Web
- CE, FCC, Rail Traffic EN50121-4 certified
- Safety EN60950-1 certified
Get In Touch
Address
759/70, Vatsala Bhuvan, Lane No.1, Prabhat Road, Deccan Gymkhana, Pune-411004, Maharashtara, India.
Phone
+91 7499103679
SALES@ORRIS-OVERSEAS.COM
ORRIS.SALES@GMAIL.COM